About Us
With more than four decades of proven success in quality roofingservices, Plusworld Roofing and Retro-Fit group is a family-owned &operated business serving.
Read MoreContact Info
- KM 21 Ojomu Royal Plaza, Lekki-Epe Expressway
- +234 700 766 3464
- info@plusworldroofing.com.ng
- Mon-Fri: 09:00am to 05.00pm
- info@plusworldroofing.com.ng
-
+234 700 766 3464
Need help? Make a Call
-
Lagos
KM 21 Ojomu Royal Plaza, Lekki-Epe Expressway
- Get An Estimate
Hydroseal Waterpoofing System
Hydroseal is designed for waterproofing all types of concrete surfaces such as concrete roof, foundation walls, basement and retaining walls. Mixed with power part and fully reinforced with fabric, it forms a hard-wearing, and flexible waterproofing system. It is a fluid applied waterproof System for roof & basement that allows design professionals to create seamless waterproof systems which have no accessories and no leakage points, 6 years renewable warranty.
Uses
Recover and New concrete roof waterproofing
Gutter of metal roof Flat and low-pitched roof waterproofing, including BUR, concrete, EPDM, Hypalon, modified bitumen, PVC, and TPO Parapet wall & Exterior wall waterproofing
Application Guidelines:
Mixing:
Hydroseal slurry is prepared by mixing Hydroseal liquid part and power part together. Add Hydroseal liquid part to a clean 5-gallon pail and mix with a slow-speed mechanical mixer. Slowing add the power part until a totally homogenous and lump-free slurry is produced. The mixed slurry must be run out in 6 hours.
Application:
Apply a 6“or 12”wide strip of ROOFMATE Base coat, Fabric, and base coat over corner, cracks and joints.
Apply one coat of Hydroseal slurry to the substrate, ROOFMATE fabric lay into the wet Hydroseal slurry, finally a second coat of Hydroseal slurry saturating the fabric from above,making sure there are no wrinkles or air pockets.Overlap fabric is about 4 inches.
Let it dry at lease 12 hours. Apply the Barrierseal slurry to the treated area one more time.
Hydroseal slurry should only be applied with roof brush. Rolling and spraying of Hydroseal slurry are absolutely forbidden.
Coverage
Hydroseal coat =400sqf/5gal/coat ,total three coats.
Clear UP
Thoroughly clean and rinse application equipment with fresh water
Warranty
6 year renewable
Standard 6 year renewable
Standard Hydroseal system (one coat Hydroseal slurry +Roofmate Fabric+ one coat Hydroseal slurry e +one coat Hydroseal slurry), Total Roofmate dry thickness should be a minimum of 1.30 mm (0.05inches ). system(one coat Hydroseal slurry+Roofmate Fabric+one coat Hydroseal M slurry e+one coat Hydroseal slurry), Total Roofmate dry thickness should be a minimum of 1.30 mm (0.05inches ).
10 year renewable
Enhanced Hydroseal system (one coat Hydroseal slurry +Roofmate Fabric+ one coat Hydroseal slurry e+ one coat Hydroseal slurry+ one coat Hydroseal slurry), Total Hydroseal dry thickness should be a minimum of 1.70 mm (0.07inches).
What are the advantages
- Protects masonry surfaces from water damage
- Will not peel off like stick-on adhesives
- System never has to be torn off Resists acid rain, and chemical pollutants from chemical spills and fallout damage.
- Meets V.O.C. emissions and regulations to eliminate facility down-time during installation
- Easy application, and clean up
- No special training or equipment required to install
- Resists ponding water
- Wear resistant and hard to damage
- Nontoxic formulation is safe to apply
English 